The T24-RA Wireless Telemetry Potentiometer Acquisition module is a high performance wireless device designed for the collection and processing of resistance related measurements. The T24-RA measures resistance and periodically transmits it.
Low power modes allow the T24-RA wireless current sensor acquisition module to ‘power down’ between transmissions or to ‘power off’ completely and can be controlled by other T24 products such as the handheld displays or a base station. The module can be configured to last several years on 2 x alkaline AA batteries or alternatively powered from 2 x NiMH or 1 x 3V Lithium.
The high accuracy, low noise measurement electronics in the T24-RA deliver high resolution, low drift results which can be user calibrated over 9 points to enable linearization and to deliver results in user definable engineering units. The results can be transmitted wirelessly to other T24 devices such as handheld displays, analog outputs and base stations etc.
Although the T24-RA modelo can be used ‘as is’ for OEM solutions there are a number of enclosure options available.
Integral antenna option offers up to 800m (2600 ft) range and external antenna options allows up to 800m (2600 ft) range in an open field site.
The licence free 2.4 GHz direct sequence spread spectrum (DSSS) radio telemetry technology offers high integrity, error free communications which can co-exist with other wireless technologies such as Wi-Fi, Bluetooth® and Zigbee®. FCC, ETSI and IC approvals.
|Radio Type||Transceiver (2 way)|
|Data Rate||250||K bits/sec|
|Integral Antenna||120 (400)||Metres (feet) *|
|External Antenna||800 (2600)||Metres (feet) *|
|*Maximum range achieved in open field site with the T24 acquisition module at a height of 3 metres (9.8 feet) above ground and T24-HS held at chest height pointing towards the acquisition module. Specification at 3V supply at 25°C|
|Sensor Excitation Voltage||2.45||2.5||2.55||VDC|
|Accuracy||-||0.01||% of full scale|
|Power Supply Voltage||2.1||3.0||3.6||VDC|
|Power Supply Ripple||50||mV ac pk-pk|
|Power Supply Current||Min||Typical||Max||Units|
|Normal Mode (Non Low Power Mode)||35||65||mA|
|Standby / Low Power Mode||5||40||uA|
|Operating Temperature Range||-40||+85||C|
|PCB Dimensions||16.8 x 37 x 6.5mm|
Module transmits and Receives giving: 1. Full error detection and correction 2. Ability to switch to low power modes 3. Calibration & configuration via radio telemetry 4. Ability to be switched from sleep to operating mode via radio 5. Calibration stored within the module 6. Remote battery check
|Potentiometer Acquisition with fitting for External Antenna||T24-RAe|
|Potentiometer Acquisition with Internal Antenna||T24-RAi|
|Wireless sensing OEM module T24-RA datasheet (English)||28/08/2015||910KB|
|Wireless telemetry potentiometer acquisition module T24-RA manual (English)||28/08/2015||1.5MB|
|T24 telemetry systems user's manual (English)||29/10/2019||11.6MB|
|T24 Toolkit v02.08.04 software - Configuration, calibration and testing of T24 range telemetry products||10/09/2019||4.8MB|
|T24 QuickView 2.1.0 software - Data visualization and acquisition with base station T24-BSu||10/09/2019||2.3MB|
|T24LOG100 v05.08.00 software for data acquisition up to 100 wireless modules||10/09/2019||14.1MB|
|T24 Windows Drivers - Development files (DLLs, COM drivers - ActiveX, .NET, LabView)||16/10/2018||6.2MB|